# Lenovo X200 / T400 / T500 / X301 common These models are sold with either 8 MiB or 4 MiB flash chip. You can identify the chip in your machine through flashrom: ```console # flashrom -p internal ``` Note that this does not allow you to determine whether the chip is in a SOIC-8 or a SOIC-16 package. ## Installing with ME firmware To install coreboot and keep ME working, you don't need to do anything special with the flash descriptor. Only flash the `bios` region externally and don't touch any other regions: ```console # flashrom -p YOUR_PROGRAMMER -w coreboot.rom --ifd -i bios ``` ## Installing without ME firmware ```eval_rst .. Note:: **ThinkPad R500** has slightly different flash layout (it doesn't have ``gbe`` region), so the process would be a little different for that model. ``` On Montevina machines it's possible to disable ME and remove its firmware from SPI flash by modifying the flash descriptor. This also makes it possible to use the flash region the ME used for `bios` region, allowing for much larger payloads. First of all create a backup of your ROM with an external programmer: ```console # flashrom -p YOUR_PROGRAMMER -r backup.rom ``` Then, split the IFD regions into separate files with ifdtool. You will need `flashregion_3_gbe.bin` later. ```console $ ifdtool -x backup.rom ``` Now you need to patch the flash descriptor. You can either [modify the one from your backup with **ifdtool**](#modifying-flash-descriptor-using-ifdtool), or [use one from the coreboot repository](#using-checked-in-flash-descriptor-via-bincfg). #### Modifying flash descriptor using ifdtool Pick the layout according to your chip size from the table below and save it to the `new_layout.txt` file: ```eval_rst +---------------------------+---------------------------+---------------------------+ | 4 MiB chip | 8 MiB chip | 16 MiB chip | +===========================+===========================+===========================+ | .. code-block:: none | .. code-block:: none | .. code-block:: none | | | | | | 00000000:00000fff fd | 00000000:00000fff fd | 00000000:00000fff fd | | 00001000:00002fff gbe | 00001000:00002fff gbe | 00001000:00002fff gbe | | 00003000:003fffff bios | 00003000:007fffff bios | 00003000:00ffffff bios | | 00fff000:00000fff pd | 00fff000:00000fff pd | 00fff000:00000fff pd | | 00fff000:00000fff me | 00fff000:00000fff me | 00fff000:00000fff me | +---------------------------+---------------------------+---------------------------+ ``` The last two lines define `pd` and `me` regions of negative size. This way ifdtool will mark those as unused. Update regions in the flash descrpitor (it was extracted previously with `ifdtool -x`): ```console $ ifdtool -n new_layout.txt flashregion_0_flashdescriptor.bin ``` Set `MeDisable` bit in ICH0 and MCH0 straps: ```console $ ifdtool -M 1 flashregion_0_flashdescriptor.bin.new ``` Delete previous descriptors and rename the final one: ```console $ rm flashregion_0_flashdescriptor.bin $ rm flashregion_0_flashdescriptor.bin.new $ mv flashregion_0_flashdescriptor.bin.new.new flashregion_0_flashdescriptor.bin ``` Continue to the [Configuring coreboot](#configuring-coreboot) section. #### Using checked-in flash descriptor via bincfg There is a copy of an X200's flash descriptor checked into the coreboot repository. It is supposed to work for the T400/T500 as well. The descriptor can be converted back to its binary form using a tool called **bincfg**. Go to `util/bincfg` and build it: ```console $ cd util/bincfg $ make ``` If your flash is not 8 MiB, you need to change values of `flcomp_density1` and `flreg1_limit` in the `ifd-x200.set` file according to following table: ```eval_rst +-----------------+-------+-------+--------+ | | 4 MiB | 8 MiB | 16 MiB | +=================+=======+=======+========+ | flcomp_density1 | 0x3 | 0x4 | 0x5 | +-----------------+-------+-------+--------+ | flreg1_limit | 0x3ff | 0x7ff | 0xfff | +-----------------+-------+-------+--------+ ``` Then convert the flash descriptor: ```console $ make gen-ifd-x200 ``` It will be saved to the `flashregion_0_fd.bin` file. #### Configuring coreboot Now configure coreboot. You need to select correct chip size and specify paths to flash descriptor and gbe dump. ``` Mainboard ---> ROM chip size (8192 KB (8 MB)) # According to your chip (0x7fd000) Size of CBFS filesystem in ROM # or 0x3fd000 for 4 MiB chip / 0xffd000 for 16 MiB chip Chipset ---> [*] Add Intel descriptor.bin file # Note: if you used bincfg, specify path to generated util/bincfg/flashregion_0_fd.bin (/path/to/flashregion_0_flashdescriptor.bin) Path and filename of the descriptor.bin file [*] Add gigabit ethernet configuration (/path/to/flashregion_3_gbe.bin) Path to gigabit ethernet configuration ``` Then build coreboot and flash whole `build/coreboot.rom` to the chip. ## Flash layout The flash layouts of the OEM firmware are as follows: ```eval_rst +---------------------------------+---------------------------------+ | 4 MiB chip | 8 MiB chip | +=================================+=================================+ | .. code-block:: none | .. code-block:: none | | | | | 00000000:00000fff fd | 00000000:00000fff fd | | 00001000:001f5fff me | 00001000:005f5fff me | | 001f6000:001f7fff gbe | 005f6000:005f7fff gbe | | 001f8000:001fffff pd | 005f8000:005fffff pd | | 00200000:003fffff bios | 00600000:007fffff bios | | 00290000:002affff ec | 00690000:006affff ec | | 003e0000:003fffff bootblock | 007e0000:007fffff bootblock | +---------------------------------+---------------------------------+ ``` On each boot of vendor BIOS `ec` area in flash is checked for having firmware there, and if there is one, it proceedes to update firmware on H8S/2116 (when both external power and main battery are attached). Once update is performed, first 64 KiB of `ec` area is erased. Visit [thinkpad-ec repository](https://github.com/hamishcoleman/thinkpad-ec) to learn more about how to extract EC firmware from vendor updates.